Quizzes on HardHat Engineer

/10
5134

Are you familiar with Centrifugal Pump?

Take this 10 Questions Short Quiz and Check Yourself.

You Need a Minimum 80% Score to Pass!!! Try Now

1 / 10

The closed impeller is used in the service with particles.

2 / 10

_____ may lead to cavitation in the pump.

3 / 10

The only difference between OH3 and OH4 types API 610 pump is the use of a rigid coupling method in OH4 compared to flexible coupling in OH3.

4 / 10

Which part of centrifugal pump transfer energy from the motor to the fluid?

5 / 10

A Centrifugal pump converts kinetic energy into the pressure head of the liquid.

6 / 10

__________ type of pump is used to inject a small fixed volume of liquid in a Chemical dosing skid?

7 / 10

______ volute design will minimize the shaft’s defection when the pump is operating outside the BEP (Best Efficiency Point).

8 / 10

The multistage pump design is used for ______.

9 / 10

Select correct API 610 Centrifugal Pump categories.

10 / 10

When vapor bubbles are created inside the pump and the subsequent collapsing of these bubbles inside the pump is known as a ________.

The average score is 69%

0%

/10
16834

Can You Read P&ID Efficiently?

Take this 10 Questions Short Quiz and Check Yourself.

You Need a Minimum 80% Score to Pass!!! Try Now

1 / 10

What is not included in a P&ID?

2 / 10

P&ID is a Piping and Internal diagram.

3 / 10

Image shown above is for __________.

Generic Valve Symbol P&ID

4 / 10

Identify the symbol shown in the image.

Main Process line with Heat Tracing

5 / 10

Isolation and shutoff valves are shown in the _______.

6 / 10

Pipe classes and pipeline numbers are shown on the Process Flow Diagram – PFD.

7 / 10

Symbole shown in this image is for ____?

Low Point Drain in P&ID

8 / 10

Identify the symbol shown in the image.

Pneumatic Connection in P&ID

9 / 10

In which part of the drawing will you look for additional information that the designer wishes you to add to make the drawing more comprehensive?

10 / 10

P&ID is also known as Process Engineering Flow Scheme (PEFS).

The average score is 67%

0%

/10
6722

Are You familiar with types of Valves used in Process Piping?

Take this 10 Questions Short Quiz and Check Yourself.

You Need a Minimum 80% Score to Pass!!! Try Now

1 / 10

Which type of the Butterfly valve is placed between pipe flanges, and the flange bolts surround the valve body.

2 / 10

Which of the following valve can be used to stop, start, and regulate the fluid flow?

3 / 10

___________ of the valve body is used when pigging is required in the pipeline.

4 / 10

In which type of gate valve the valve disk is threaded internally?

5 / 10

_________is similar to the globe valve in design.

6 / 10

Which type of bonnet design is used in the high-pressure applications?

7 / 10

For a non-rising stem valve, the stem will go up while opening the valve and move down when you close the valve.

8 / 10

The removable and replaceable internal parts of the valve that come in contact with the flow medium are collectively known as valve ____.

9 / 10

________ valve is used in field analog instruments to control flow.

10 / 10

Select the correct type of disk in the Gate valve.

The average score is 54%

0%

/10
5694

Are You familiar with Flanges and Olets used in Process Piping?

Take this 10 Questions Short Quiz and Check Yourself.

You Need a Minimum 80% Score to Pass!!! Try Now

1 / 10

Which type of flange is used where frequent dismantling is required, and space is constrained.

2 / 10

Which flange is not suitable for small-size piping?

3 / 10

Lap flange is available in limited Size of NPS 4” and below.

4 / 10

Flanges are manufactured using which method?

5 / 10

A full-face gasket is used when a raised face flange is used.

6 / 10

Which three components are used to form flanged joints? Select all three.

7 / 10

Dimensions of Pipe Flanges and Flanged Fittings up to size NPS ½” to 24” are given in which standard?

8 / 10

Select the correct carbon steel flange material grade.

9 / 10

What type of gasket is used with RTJ face flange?

10 / 10

Weldolet’s end is suited for the socket welding connection.

The average score is 65%

0%

/10
7516

Are You familiar with Pipe Fittings used in Process Piping?

Take this 10 Questions Short Quiz and Check Yourself.

You Need a Minimum 80% Score to Pass!!! Try Now

1 / 10

Hydrotest is used to qualify the design of the pipe fitting.

2 / 10

What is the radius of the long radius Elbow?

3 / 10

Only seamless pipes are used to produce wrought fittings.

4 / 10

In ________, the diameter of the branch is the same as the diameter of the Run (Header) Pipe.

5 / 10

Pipe Fittings are available only in butt weld end connections.

6 / 10

_____ pressure class fittings are available only in threaded type.

7 / 10

_______ are not standard pipe fittings and they are fabricated from pipes.

8 / 10

9000 pressure class fittings are available in only the socket weld type.

9 / 10

Dimensions of the pipe fittings (Wrought Product (WP)) are given in which standard?

10 / 10

Elbows are mainly available in the following types?

The average score is 68%

0%

/10
21551

Are You familiar with Pipes used in Process Piping?

Take this 10 Questions Short Quiz and Check Yourself.

You Need a Minimum 80% Score to Pass!!! Try Now

1 / 10

Dimensions of the Carbon & Alloy Steel pipes are covered in the following Standard.

2 / 10

Which document is used to specify the type of the components that will be used in the given piping system?

3 / 10

Above 14″ pipe OD is the same as the size mentioned in OD.

4 / 10

Which one is not used to indicate pipe size?

5 / 10

What method is used to identify the material pipeline transporting from the outside?

6 / 10

Which type of pipe is used for critical services such as high pressure?

7 / 10

What is Small Bore Pipe?

8 / 10

Dimensions of Stainless Steel pipes are given in which standard?

9 / 10

Which welding method is used to manufacture large dia pipe?

10 / 10

What NPS (Nominal Pipe Size) indicates?

The average score is 67%

0%

/10
4177

Are you familiar with Types of Gasket?

Take this 10 Questions Short Quiz and Check Yourself.

You Need a Minimum 80% Score to Pass!!! Try Now

1 / 10

Identify the type of gasket shown in the image.

Cam Profile Gasket

2 / 10

Which type of gasket is used with raised face flanges?

3 / 10

Metallic Gasket dimensions are covered in which standard?

4 / 10

The hardness of the O-ring RTJ gasket shall always be less than flange material by at least ____ BHN.

5 / 10

Select two types of metallic gasket that are used with RTJ flanges.

6 / 10

A Spiral Wound Gasket inner ring is used to provide additional support to the winding material.

7 / 10

Which type of gasket is used with high-pressure class flanges in critical services?

8 / 10

The primary function of gaskets is to stop leakage from the welded joint.

9 / 10

Which non-metallic gasket can be used for high-temperature service?

10 / 10

Low tension bolting is used with metallic gaskets.

The average score is 62%

0%

3315

P&ID Final Quiz

This is the final Quiz to check your understanding of P&ID.

1 / 25

In which part of the drawing will you look for additional information that the designer wishes you to add to make the drawing more comprehensive?

2 / 25

Identify the symbol shown in the image.

Pneumatic Connection in P&ID

3 / 25

Identify the symbol shown here.

Floating roof tank

4 / 25

P&ID is a Piping and Internal diagram.

5 / 25

Design pressure and temperature are shown in the _______ Static Equipment Data table.

6 / 25

Identify the symbol of the instrument shown here.

Panel Mounted Instrument

7 / 25

_________  shows an overview of a plant, unit, or process in the easiest form possible.

8 / 25

Pipe classes and pipeline numbers are shown on the Process Flow Diagram – PFD.

9 / 25

The stream table is only shown on the PFD (Process Flow Diagram).

10 / 25

P&ID shows all the equipment, including installed spares, and associated piping including drain and vent line.

11 / 25

Identify the type of heat exchanger shown in the image.

Heat Exchanger with U Tube bundle

12 / 25

A single PFD can have multiple P&IDs.

13 / 25

Identify the symbol shown in the image.

T-type Strainer

14 / 25

P&ID is a _______  representation of the actual process plant using various symbols.

15 / 25

The equipment detail block shown in the image is available in ______.

PFD Equipment detail block

16 / 25

Symbole shown in this image is for ____?

Low Point Drain in P&ID

17 / 25

Image shown above is for __________.

Generic Valve Symbol P&ID

18 / 25

What is not included in a P&ID?

19 / 25

Identify the symbol shown in the image.

Main Process line with Heat Tracing

20 / 25

The symbol shown here is for Spectacle Blind “Normally Open” in P&ID

Spectacle Blind, Normally Closed in P&ID

21 / 25

What is not included in the P&ID?

22 / 25

P&IDs are developed using already available ______.

23 / 25

Isolation and shutoff valves are shown in the _______.

24 / 25

P&ID is also known as Process Engineering Flow Scheme (PEFS).

25 / 25

The symbol shown in the image is of 24″ ______.

Manhole entry

Your score is

The average score is 72%

0%

/25
7056

Take this 25 Questions Long Quiz and Check Yourself.

Random questions from all piping components topics, including pipe, fittings, flanges, olets, valves, and gaskets.

You Need a Minimum 70% Score to Pass!!! Try Now

1 / 25

_______ are used as an alternative to flanges connection in low-pressure small bore piping where the dismantling of the pipe is required more often.

2 / 25

Only seamless pipes are used to produce wrought fittings.

3 / 25

Concentric reducer which is also known as a _________.

4 / 25

_____ pressure class fittings are available only in threaded type.

5 / 25

Hydrotest is used to qualify the design of the pipe fitting.

6 / 25

In ________, the diameter of the branch is the same as the diameter of the Run (Header) Pipe.

7 / 25

Which type of gate valve is used in slurry and powder product application?

8 / 25

Which type of disk design in the globe valve provides better throttling?

9 / 25

Which standard gives the list of Trim materials that can be used in the valve?

10 / 25

________ valve is used in field analog instruments to control flow.

11 / 25

Which valve is ideally suited for the handling of slurries, liquids with large amounts of suspended solids, and systems that convey solid material pneumatically?

12 / 25

___________ of the valve body is used when pigging is required in the pipeline.

13 / 25

Gate Valve can be used as a control valve.

14 / 25

Which type of flange is used where frequent dismantling is required, and space is constrained.

15 / 25

Orifice Flanges are used for ______.

16 / 25

Which type of flange provide highest level of joint integrity?

17 / 25

The following is used to specify Pipe dimension?

18 / 25

The steel coil is used to manufacture which type of pipe?

19 / 25

Which type of pipe is used for critical services such as high pressure?

20 / 25

The higher the schedule number lower the thickness of the pipe.

21 / 25

Which welding method is used to manufacture large dia pipe?

22 / 25

Identify the type of gasket shown in the image.

Cam Profile Gasket

23 / 25

Select two types of metallic gasket that are used with RTJ flanges.

24 / 25

The primary function of gaskets is to stop leakage from the welded joint.

25 / 25

Which non-metallic gasket can be used for high-temperature service?

The average score is 62%

0%